What Kind Of Paint To Use On Pressed Wood

Download Article

Particle board, or chipboard, is a very lightweight type of wood that's oftentimes found in inexpensive furniture or small decorations. Although it is yet wood, it's a lot softer and easier to damage than regular lumber, making information technology more than probable to get scratched and more difficult to pigment. If you want to pigment some particle lath, sand information technology down lightly, utilise a thin layer of primer, and encompass it with several coats of paint to get the look you're after.

1
Remove any hardware or accessories y'all don't want to paint over. If you're painting particle board furniture or touching up cabinets, there may exist metal fittings or handles that yous want to keep unpainted. Employ a screwdriver to carefully remove any hardware, fittings, or accessories fastened to the particle board that you don't want to be painted.^[1]
- If you're painting particle board article of furniture, it might be easier to disassemble it and paint each slice individually. If you can, follow the assembly instructions in reverse to carefully take apart the item you want to paint.
- Make sure that y'all store all of the fittings, hardware, screws, and anything else you take out of the particle lath somewhere where it won't get lost.
2
Sand the board downward with 120-dust sandpaper. The lamination or sheen on the particle board volition prevent paint from sticking to it. Use a medium to fine dust sandpaper, around 120-grit, to sand down the face of the particle board yous want to pigment. Sand information technology down lightly, only enough to remove the shine from it and expose the wood.^[ii]
- Particle board is a very soft wood, which makes it easier to work with and motility around, but as well easier to scratch and impairment. Use merely light pressure when sanding to avoid damaging your particle board.
- Employ a vacuum cleaner or shop-vac to remove any dust that comes off the board while sanding information technology.
- To avoid getting the inside of your dwelling messy, sand, prime number, and paint your particle board outside.
Ad
3
Coat the particle board with a layer of oil-based primer. The nearly difficult part of painting particle lath is getting the paint to adhere to the surface. Once the board has been sanded down, utilise a wide paintbrush to comprehend it with a single layer of oil-based primer. Make sure to get into any hard to accomplish areas so that the entire surface is covered.^[3]
- A water-based primer will seep into the particle board and crusade it to swell up. Always use an oil-based or solvent-based primer when painting particle boards.
- Oil-based primer should be available at your local hardware shop. If you're unsure which type to use, inquire an employee for aid choosing the right primer and pigment for you lot.
4
Give the primer 30 minutes to an 60 minutes to fully dry. Your coat of primer needs to exist completely dry earlier you can begin painting the wood. Leave the particle board sitting out in the lord's day for 30 minutes to an hour to give it plenty of time to completely dry.^[4]
- Check the manufacturer's instructions for your called primer for more specific advice on how long it will accept to dry.
- You lot can bank check if the primer is fully dry by scratching at information technology lightly with a fingernail. If the primer is dry, a fingernail scratch won't leave a mark or remove any primer.^[5]
Advertisement

1
Cover the board with a coat of oil-based paint. Once the particle board has been primed, you can begin coating it with your pigment of choice. Dip a broad-bristled paintbrush or a paint roller into an oil-based paint in your desired color. Piece of work slowly and methodically to embrace the entire surface with a coat of paint.^[6]
- If you lot take a paint sprayer, y'all could likewise use this to evenly paint the particle lath. Piece of work in sparse layers to make sure the paint is practical evenly and dries quickly.
- Oil or lacquer-based paints volition piece of work best for painting particle boards. Withal, if yous have primed the forest with an oil-based primer, you should exist able to apply water-based paint without the particle lath absorbing any h2o.
- A multifariousness of different colored paints should exist available at your local hardware store. Choose one that you similar and that will piece of work well with the other colors in the room where y'all'll put your finished particle board.
2
Let the paint dry for xxx minutes to an hour. One time you've finished the kickoff coat of paint on your particle board, leave it to dry. Give your pigment around an hour in the sunday to brainstorm to dry. If you can bear upon the paint lightly without getting whatever pigment on your finger, the pigment should be dry plenty to use a second coat.^[vii]
- If you alive in a colder or more than humid surround, it may have longer for your paint to dry. It'south better to give it more time than it needs to dry out than it is to move on while the pigment is still wet.
- Consult the manufacturer's instructions on your chosen paint for more specific advice on how long it will take to dry.
iii
Apply some other coat of pigment and allow information technology dry. When the pigment is dry out to the touch on, apply a 2nd layer of paint using the aforementioned castor or roller. Leave the paint to dry for another 30 minutes to an hour. Repeat this process until you are happy with the expect of your particle board.^[8]
- With most particle board, it will take betwixt ii and iv layers of paint to completely cover the primer.
iv
Reassemble and reattach the hardware. With your particle board painted and dry out to the touch on, you can brainstorm putting information technology back together. Reassemble the particle board if you disassembled information technology to paint information technology, and reattach any hardware or fittings until everything is put back together.^[9]
- The pigment may still be soft when you begin reassembling your particle board, so make sure you work carefully. Alternately, you tin can leave your particle board to dry for 12 to 24 hours before reassembling information technology.
Advertisement

Add together New Question

Question

Do you need to sand particle lath before painting?

Crystal Chadwick is a Licensed Full general Contractor and the Possessor of Yin & Yang Construction out of Salt Lake Metropolis, Utah. With over 16 years of experience in the structure manufacture, she specializes in remodels, repairs, and handyman services. Crystal leads her team with vision and a detail-oriented approach, allowing them to provide quality work and design to their clients.

Licensed General Contractor

Proficient Reply

Yes, this is a good idea. Particle board is a pretty rough cloth, so have some time to sand whatever rough edges before y'all get started.
Question

Tin I use 2-in-one primer and paint instead of priming separately?

Crystal Chadwick is a Licensed Full general Contractor and the Owner of Yin & Yang Construction out of Salt Lake Metropolis, Utah. With over xvi years of experience in the construction industry, she specializes in remodels, repairs, and handyman services. Crystal leads her squad with vision and a detail-oriented arroyo, assuasive them to provide quality work and blueprint to their clients.

Licensed General Contractor

Skilful Answer

You could, just I wouldn't recommend it. You'll become better results if you lot prime number first, then employ two coats of paint later on that.

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Near paint will take at least a week to completely dry out and cure. If you are painting particle board furniture, avert putting anything heavy on it for at to the lowest degree one week so as to not hazard damaging the paint.
Y'all could also pigment particle boards with several thin layers of spray paint. Make sure you do and then in a well-ventilated surface area to avoid inhaling any overspray.
If yous notice the paint or primer bubbles or spotting as it dries, information technology may be a sign that you didn't sand downwards that area well enough. Wait for the section to dry out, sand it downwardly further, and reapply the primer or paint.

Work outside or in a well-ventilated area when painting and sanding. This will go on the within of your abode clean and free of potent paint fumes.

Advertizing

Things You'll Need

120-grit sandpaper
Oil-based primer
Paintbrush or paint roller
Paint

Near This Article

Cheers to all authors for creating a page that has been read 106,103 times.

Did this article help y'all?